ccs,pd2,PD2-1012(A),PD2-1024(A),PD2-3012(A),PD2-3024(A),PD2-5012(A),PD2-5024(A),PD2-3012-2(A),PD2-3024-2(A),PD2-3012-4(A),PD2-3024-4(A),PD2-3012-8(A),PD2-3024-8(A)
Welcome to JIDIEN
Product Introduction 產品資訊

CCS LED光源 PD2 Series 控制器

Digital Control Unit
These CCS digital control units can be used for LED light units. For detailed information, please refer to the table below.
  • Model name

    PD2-1012(A)

    PD2-1024(A)

    PD2-3012(A)

    PD2-3024(A)

    PD2-5012(A)

    PD2-5024(A)

    PD2-3012-2(A)

    PD2-3024-2(A)

    PD2-3012-4(A)

    PD2-3024-4(A)

    PD2-3012-8(A)

    PD2-3024-8(A)

    Input voltage

    100 to 120 VAC

    100 to 240 VAC

    Input current*1

    0.25 A typ.

    0.78 A typ.

    1.3 A typ.

    0.78 A typ.

    Frequency

    50/60 Hz

    Inrush current

    15 A typ.

    No. of channels

    1 channel

    1 channel

    1 channel

    1 channel

    1 channel

    1 channel

    2 channels

    2 channels

    4 channels

    4 channels

    8 channels

    8 channels

    DC output voltage

    12 V

    24 V

    12 V

    24 V

    12 V

    24 V

    12 V

    24 V

    12 V

    24 V

    12 V

    24 V

    Output voltage

    9.5 W max.

    9.0 W max.

    28 W max.

    28 W max.

    46 W max.

    46 W max.

    28 W max.

    28 W max.

    27 W max.

    27 W max.

    25 W max.

    25 W max.

     

    Intensity control

    Intensity control method: 62.5 kHz PWM control

    Manual: 16-step intensity control using coarse and fine rotary switches on the front panel

    External: Intensity control using 8-bit parallel signal

     

    External control input

    Input circuit: Pull-up of +5.0 V internally by use of resistor (4.7 kΩ)

    Input circuit: Pull-up of +5.0 V internally by use of resistor (2.2 kΩ)

     

     

    HS-CMOS input: Low level of max. 1.0 V, high level of 3.5 V or more

    External control connector

    D-sub 15-pin (plug)

    D-sub 25-pin (plug)

    Lights ON/OFF control

    ON/OFF control during manual intensity control: Ø3.5 mm microphone jack

    ON/OFF control during external intensity control: D-sub 15-pin ON signal (not synchronized with writing sequence)

    Manual/External: D-sub 25-pin ON signal

    (not synchronized with writing sequence)

    Light ON/OFF response time

    OFF→ON: 10 μs typ., ON→OFF: 10 μs typ.

    Startup time

    0.5 sec typ.

    Output overcurrent protection

    Operates at 107% of the output current. Reset by turning the power off and then on again.

    Operating environment

    Temperature: 0 to 40°C, Humidity: 20% to 85%RH (with no condensation)

    Storage environment

    Temperature: -20 to 60°C, Humidity: 20% to 85%RH (with no condensation)

    Weight

    0.7 kg max.

    1.1 kg max.

    1.3 kg max.

    1.1 kg max.

    1.2 kg max.

    1.5 kg max.

    Accessories

    3-prong AC cord with ground terminal*2 (2 m) x 1, Instruction Guide x 1

Copyright © 中和碁電股份有限公司. All Rights Reserved.